IOI

 "1394R-B4 is a four ports IEEE1394b repeater, extending your signal an additional 4.5 meters. It's easy to setup and there is no configuration necessary, like all IEEE1394 compliant hardware. Technical Specification * Fully Supports Provisions of IEEE P1394b Revision 1.33+ at 1-Gigabit Signaling Rates * Fully Supports Provisions of IEEE 1394a.2000 and 1394.1995 Standard for High Performance Serial Bus * Fully Interoperable With Firewire., i.LINK., and SB1394., Implementation of IEEE Std 1394 * PHY Chip: TI TSB81BA3D. * 1394 Bus Transfer Rate: 100/ 200/ 400/ 800 Mbps * Device Interface: Provides Four Fully Backward Compatible, (1394a.2000 Fully Compliant) Bilingual P1394b Cable Ports at up to 800 Megabits per Second (Mbits/s) * DC Power input Connector: Walkman-type 2.0 mm DC Jack * Power Input Range: DC 8V~30V, max. 1.35A * Power Consumption: Under 1.5 Watts. * Number of ports: Four Bilingual Cable Port with Jackscrew Lock Holes * Power LED Physical Dimensions * 92(W)x62(D)x20.6(H)mm Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce. bez napájecího zdroje - dodáván samostatně - viz související produkty "

 "This FireWire card by IOI expands your PC by two external and one internal FireWire A port. You can connect several FireWire devices like e.g. external enclosures with internal hard disk or CD drive, camcorder, internal FireWire devices etc. to the card. Specification • IOI item number: FW-PCI3201 • 2 x external FireWire A (IEEE 1394a) • 1 x internal FireWire A (IEEE 1394a) • Low profile PCI form factor • Data transfer rate up to 400 Mb/s • Chipset: Texas Instruments TSB43AB23 • 1 x internal 4 Pin Molex 12 V power connector System requirements • Window 98 SE/Me/2000/XP/Vista/7, Mac OS 8.6 or higher, Linux 2.4.X • One free PCI card slot Package content • PCI card • Low profile bracket Package • White box - Záslepka do slotu pro low profile je dodávána jako samostatné příslušenství"

 "FWB-PCI3202B -3x FW-B 800 externí -Chip: Texas Instr. TSB83AA23 -33-MHz / 32-Bit PCI-Power: 3,5" IDE 4pin - Windows 2000/XP/Vista, MacOS 10.4. nebo vyšší, Linux Kernel 2.6.23 nebo vyšší Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce. Highlight * 32-bit PCI Host interface * Three External Bilingual (1394b) connectors (with screw lock) * Big IDE 4-pin DC Power Connector for supplying power to the 1394 Bus Introduction FWB-PCI3202B is a three port OHCI 1.1 Compliant FireWire 800 (IEEE-1394b) PCI Host Adapter featuring Texas Instruments OHCI 1.1 Compliant FireWire 800 (IEEE-1394b) Single Chip Host Controller. Technical Specification Host Bus: * 33-MHz/32-Bit PCI Interface * 3.3-V and 5-V PCI Signaling Environments IEEE 1394 Std Support: * Fully Supports Provisions of IEEE P1394b Revision 1.33+ at 1-Gigabit Signaling Rates * Fully Supports Provisions of IEEE 1394a.2000 and 1394.1995 Standard for High Performance Serial Bus * Fully Interoperable With Firewire., i.LINK., and SB1394., Implementation of IEEE Std 1394 1394 Bus Transfer Rate: Provides three fully backward-compatible, (IEEE Std 1394a-2000 fully compliant) Bilingual IEEE Std 1394b-2002 cable ports at S100/S200/S400/S400B/S800 megabits per second (Mbits/s). IEEE-1394 to PCI Controller Texas Instruments TSB83AA23 DV and DA Enhancement: * Digital Video and Audio performance enhancements. * Extended resume signaling for compatibility with legacy DV components. Power Management : D0, D1, D2, and D3 power states and PME events per the PCI Bus Power Management Interface Specification Number of ports: * FWB-PCI3202B: Three External Bilingual Ports (with screw lock) Bus Power Connector: Big IDE 4-pin DC Power Connector Operating System Requirements * The 1394b function (host driver) is supported (built in) by the following OS: o Windows 2000 SP4 or later o Windows XP SP2 or later o Windows Vista SP1 or later o Mac OS 10.4 or later o Linux kernel 2.6.23 or later. "

 "Highlights * Host Bus: 1-lane 2.5 Gb/s PCI Express * Eight (8) isochronous transmit/receive contexts * Deep 8 Kbyte isochronous transmit/receive FIFOs * Complies with 1394 OHCI draft 1.2 * Three external 1394 ports * Bilingual ports with Screw Holes for thumbscrew locking Type 1394b Cable The FWB-PCIE1X21A combines an OHCI (Open Host Controller Interface) and a high-performance, standards-compliant PCI Express 1.1 host system interface to provide S800 1394b-2002 compliant throughput in a small PCB (Printed Circuit Board) and low power dissipation. MultipleVCs (Virtual Channels) on the PCI Express link provide native support for QoS (Quality of Service) transmission for real-time and multimedia applications in a standards-based framework, ensuring compatibility with current and future operating systems. Active-state power management allows dynamic power management during periods of reduced network activity. Technical Specifications PCI Express: * Designed for compliance with PCI Express. * Multiple virtual channel (VC0,VC1 ) support fordiffe-rentiating 1394 isochronous traffic. * Supports eight user-programmable traffic classes. * 64-bit and 32-bit platform support. * Interrupts via legacy INTx interface or message sig-naled interrupt (MSI). * Supports PCI Express clock power management viaCLKREQN signal for form factors that support thisprotocol. * Supports all linkpowermanagement states (L0,L0s,L1,andL2/L3) and active state power management(ASPM). * Supports wake-up from a low-power state via in-bandbeacon signaling and side-band WAKE_N signal. OHCI (Open Host Controller Interface) * Enhanced with the OHCI 1.2 draft specification for 1394b-2002 PHY full operational compliance. * OHCI 1.0 backwards compatible. Configurable via EEPROM to operate in either OHCI 1.0 or OHCI 1.1 mode. * 8 Kbyte isochronous transmit FIFO. * 4 Kbyte asynchronous transmit FIFO. * 8 Kbyte isochronous receive FIFO. * 8 Kbyte asynchronous receive FIFO. * Dedicated asynchronous and isochronous descriptor-based DMA engines. * Eight isochronous transmit contexts. * Eight isochronous receive contexts. * Supports parallel processing of incoming physical read and write requests. * Supports up to 48-bit addressing per OHCI specifica-tion for the physical DMA transfers. 1394b-2002 Link * Cycle master and isochronous resource manager capable. * Supports 1394a-2000 and 1394b-2002 acceleration features. 1394b-2002 PHY * Provides three IEEER 1394b-2002 compliant ports sup-porting 1394b-2002 speeds of 800 Mbits/s and 400Mbits/s while maintaining backward compatibility to IEEE 1394a-2000 speeds of 100 Mbits/s, 200Mbits/s, and 400 Mbits/s over 4.5 m copper. * Fully supports provisions of IEEE 1394a-2000 and 1394-1995 standards for high-performance serial bus. * Link is not required for hub operation. * Supports extended BIAS_HANDSHAKE time for enhanced interoperability with camcorders. * Does not require external filter capacitor for PLL. * Supports arbitrated short bus reset to improve utiliza-tion of the bus. * Supports ack-accelerated arbitration and fly-by concat-enation. * Supports PHY pinging and remote PHY access pack-ets. * Fully supports suspend/resume. Reports cable power fail interrupt when voltage at CPS ball falls below 7.5 V. Number of Ports: * Two Bilingual ports with Screw Holes for thumbscrew locking Type 1394b Cable+ One Firewire 1394a Cable Port Bus Power Connector: * Big IDE 4-pin DC Power Connector Operating System Requirements * Windows 2000/XP//7 and Windows Server 2003 * Mac OS 10.4.8 or later * Linux 2.6.X Certifications * CE Test: Pass * FCC Test : Pass * VCCI Test: Pass * RoHS Test : Pass Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce. "

 "2-port OHCI Compliant FireWire 800 (IEEE 1394b) & GOF (DUPLEX LC) to PCI-Express Host Adapter featuring Ti TSB82AA2 IEEE 1394 Host Controller GOF= Glass optical fiber(Glasfaser) The FWB1GLC-PCIE10 is a 2-port FireWire800 (IEEE 1394b) & GOF(DUPLEX LC) to PCI Express Host Adapter. FWB1GLC-PCIE10 is designed with three key components. * PCI Express to PCI Bus Translation bridge. * Texas Instruments TSB82AA2 --- IEEE 1394b OHCI-Lynx Controller. * Texas Instruments TSB81BA3 --- IEEE 1394b 3-port Cable Transceiver/Arbiter. The PCI Express to PCI local bus translation bridge takes advantages of the 2.5 Gb/s burst rate of 1-lane PCI Express bus and the PCI bus interface is connected to a IEEE 1394b OHCI-Lynx host controller and a three-port 1394b PHY. This solution provides full PCI Express and 1394b&GOF functionality and performance. Technical Specification PCI Express and PCI: * Supports 1-lane 2.5 Gb/s PCI Express. * Utilizes 100-MHz Differential PCI Express Common Reference Clock * Fully Compliant with PCI Express Base Specification, Revision 1.0a * Packetized serial traffic with PCI Express split completion protocol * Automatic retry of bad packets * 8b/10b signal encoding * In-band interrupts and messages * Support of message signaled interrupts * Fully Compliant with PCI Local Bus Specification, Revision 3.0 * PCI Bus Power Management Interface r1.1 Compliant IEEE 1394 Std Support: * Fully Supports Provisions of IEEE P1394b Revision 1.33+ at 1-Gigabit Signaling Rates * Fully Supports Provisions of IEEE 1394a.2000 and 1394.1995 Standard for High Performance Serial Bus * Fully Interoperable With Firewire., i.LINK., and SB1394., Implementation of IEEE Std 1394 1394 Bus Transfer Rate: * Provides two IEEE Std 1394b-2002 fully compliant cable ports at 100/200/400/800 megabits per second (Mbits/s). Fiber Optical Port: * With one Agilent HFBR-5911L (DUPLEX LC) Small Form Factor Fiber Optic Transceiver. * Compliant with Specifications for IEEE 802.3 Gigabit Ethernet (1.25Gbd) 1000BASE-SX * 850nm VCSEL(Vertical Cavity Surface Emitting Laser) * Maximum link lengths: V 220 m Links in 62.5/125 gm MMF 160 MHz*km Cables V 275 m Links in 62.5/125 gm MMF 200 MHz*km Cables V 500 m Links in 50/125 gm MMF 400 MHz*km Cables V 550 m Links in 50/125 gm MMF 500 MHz*km Cables * Laser AEL Class 1 (eye safe) per: VUS 21 CFR(J) VEN 60825-1 (+All) Number of Ports: External: * Two Bilingual 9pin with Jackscrew holes Provides Two Fully Backward Compatible, (1394a.2000 Fully Compliant) Bilingual P1394b Cable Ports at up to 800 Megabits per Second (Mbits/s) * One GOF(DUPLEX LC) Port Power Management: D0, D1, D2, and D3 power states and PME events per the PCI Bus Power Management Interface Specification Bus Power Connector: Big IDE 4-pin DC Power Connector Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce. "

 "The Delock PCI Express card powered by IOI expands your PC by two external FireWire 400 ports. You can connect devices like e.g. external enclosure, digital cameras, camcorder, adapter, etc. to the card. Specification • IOI item number: FWX2-PCIE10-2 • External: 2x FireWire IEEE 1394A • Internal: 1x 12V power connector 4-Pin • 2x IEEE 1394a Single Chip Host Controller (TSB43AB22A) • Data transfer rate up to 400 Mbps • Supports OHCI specifications 1.1 • PCI Express x1 Standard • Supports PCI Express 1.0a specification System requirements • Windows 2000/XP/Server-2003/Vista, Mac, Linux 2.6.x • PC with one free PCI Express Slot Package content • PCI Express card Package • Box Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce. "

 "- Umožňuje připojení SATA zařízení (jako jsou například pevné disky) na IDE rozhraní Pozn.: K opačnému připojení (IDE zařízení na SATA rozhraní) použijte kód 322163 IOI ref.: IDE-SATA01 - pro všechny SATA HDD - bulk - Chip:Marvell 88SA8040 Both ATA and ATAPI devices are supported using the same firmware. It allows SATA drives (Master or Slave) to be connected to ATA host controller. IDE-SATA01 provides the perfect solution for legacy ATA host controller to attach new SATA devices. Specification • Compliant to Serial ATA specification 1.0 • Ultra ATA/133 Parallel interface • 4-pin FDD Power connector • Jumper for selecting Master and Slave • Supports PIO and DMA modes • Chipset: Marvell 88SA8040 • Dimension 10.09 x 2.54 cm • For Windows 98SE/ME/2000/2003/XP, Mac OS 9.1 or higher and Linux System requirements • a free IDE port • Windows 98SE/ME/2000/2003/XP, Mac OS 9.1 or higher and Linux Package content • SATA- IDE converter • 4-pin power cable "